H&G Technology Co., LTD

  • banner

​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm

​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm 1
​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm 1
​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm 2
​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm 3
​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm 4
​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm 5
Product Name : ​GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm
Product ID : HAG-​GT003
Type : gt003
GPS Precision : 10m(2D RM)
GSM : 850/900/1800/1900 Quad band
Size : 13*8.7*6cm 
Weight : 0.185kg

GPS Tracker
GT003 Vehicle GPS GPRS Tracker Tracking Over Speed+Viberation Alarm


Online Realtime Tracking and Playback Platform
Please Notice:Now our platform support these countries,please check below before you buy it:
Asia & Middle East:Singapore,HongKong,Taiwan,Indonesia,the Philippines,India,Vietnam,Thailand,Pakistan,Iraq,
Malaysia,Syria,Saudi Arabia,Israel,Jordan,Lebanon
America:USA,Canada,Mexico,Brazil,Costa Rica,Honduras,Panama,Guatemala,Bolivia,Uruguay,Paraguay,Columbia,
Africa:Angola,Egypt,Morocco,Tunisia,South Africa,Nigeria,Cameroon,Madagascar,Kenya,Libya,Guinea,Mali



It is also can be used via SMS Longitude and Latitude without platform.
2. Technical parameter 
1).GSM:850/900/1800/1900 Quad band
2).GPRS: Class12, TCP/IP
3).Working Voltage:9-50V DC
4).Working current:22mA (12vDC)
5).Working current:12mA (24vDC)
6).GPS locating time:Cold start=38s(Open sky)  Warm start=32s
                                            Hot start=2s(Open sky)
7).GPS Precision:10m(2D RM)
8).Working temperature:-20C~+70C
9).Working humidity:20%~80%RH

3.Out look


4. Device status indicators

4.1 Connect DC 9-24V power supply and the red LED will light continuously.

4.2 The green LED glistens when searching the GPS signals. When GPS works, the LED lights continuously.

4.3 The intermediate blue LED (GSM signal state)

    GSM signal is normal, blue LED light long bright. No GSM signal, the blue LED flashes.

    GPS LED not fixed, flashes(0.2 sec/2 sec),Positioning long bright;

        GSM LED no signal, flashes(0.2 sec/2 sec),Signal normal long bright;

       Power LED: long bright;

    All LEDS will turn off after 5 minutes. When there is a new call, the LEDs will relight and turn off 5 minutes later.

5. Installation

5.1 Preparation for the installation

5.1.1 Product Check. Open the packing box and check the devices model and accessories. If the model is wrong or the accessories not complete, please contact the dealer.

5.1.2 Choose SIM card. Please insert a SIM card to the device. Please take dealers advice as reference.

5.1.3 SIM card installation. Discharge the cover of the device and uncover the SIM card holder. Then insert the SIM card and cover SIM card holder (as follows).


5.1.4 Put back the front cover and screw it up.

5.1.5 Connect the device to the 9-24V power supply.(the red LED constant glow)

5.1.6 Install the device in the hidden place of the car;

The SIM card must be with GPRS function and enough deposit. If your SIM card need input PIN when power on, please cancel it.

5.2 Installation

The GPS tracker must be installed under professional personnel.


1) Please install the device in the hidden place as followings:

Under Front windshield;

In the front instrument panel;

Under back windshield;

2) Avoid being placed with signal radiators like reverse sensor ;

3) The device has GSM antenna and GPS antenna inside. Please ensure the receiving side of the device is face up and without metal cover.

Note:The metal cover will lessen the receiving of GPS signals.6. The device connecting requirements.


General Waterproof design

6. Device wiring requirements

6.1 The device power supply is DC 9-24V. The red line is positive pole while the black line is negative pole.

6.2 The negative pole of power supply connects with ground or the metals. Please do not connect with other ground lines.

6.3 When finishing the power supply wire connection, please make the plug of power supply to the device.



Relay for remote cutting off oil and power control(NOT included in the package);this accessory is not necessary,

please click and buy it at 5USD below if you need :


7. The Device Working

7.1 Power on: the device will be power on when connecting to the current. Then the three LED indicators will light continuously. The device will upload the data to the online platform (the default interval of uploading data is

 10seconds). When the car is in static state for a long time, the device will be in energy saving mode and it will be more smart and precise.

7.2  Power off:Pull off the power plug then power off the device.


8. User Settings

8.1 Set class instruction




Text command









Command Description

1)Center number can control the oil and power and resume factory settings

2) Center number can receive the call and text of vibration alarm and over speeding alarm.

3) SIM must display the income call number to control oil and power.

4) Only one number can be center number.

5) Change center number must resend the command.

6)Add new center number by CETNER,A, and delete by CENTER,D

Command Feedback

Successful Setting:SET CENTER TEL OK!



Text command



APN Setting

APN,apn[,username, password]



Command Description

APN differs according to the local telecom operators.

For example:APN request password,please refer to Sample1,and Sample2 for no password.

Command Feedback

Successful Setting:SET APN OK!



Text command



TIMEER Parameter setting

If you need any information before purchase, you can click our online service, If it is not availabl
Your name:
     Items marked with * have to be filled in